TSS-4000
TOTAL SPEAKER SOLUTIONS
TSS-FMK4000
Owner’s Guide
Important Notes:
1) In order to horizontally flush-mount the TSS-CENTER4000 in a wall
with standard 16" spacing between the studs, some modification to
that area of the wall will be necessary.This type of installation will
require a professional licensed contractor to install horizontal braces
that comply with the customer’s local building codes.
2) For a satellite installation, follow all the steps but cut the hole
in a vertical direction, perpendicular to the floor. See exploded view
on page 7.
Step One
Remove both end caps of the speaker by unscrewing the single
center screws.
Speaker
End Cap
Center Screw
1/4-20 x 3/4" Screw
Step Two
Attach both of the end brackets to the speaker ends with the
1/4-20 x 3/4" flat-head machine screw, as shown.
1/4-20 x 3/4"
Flat-Head Machine Screw
End Bracket
1/4-20 x 3/4"
Flat-Head
Machine Screw
End Bracket
3
TSS-FMK4000
Step Three
After you have found the correct placement on the wall for the
speaker, use the template provided to draw the exact-sized hole
required. Make sure to use a level when positioning the template
to ensure that your installation is level.Then cut out the drywall
to create the hole.
Wall
NOTE: The hole for
the speaker should be
22-1/2" x 4-3/8".
Template
Screw Holes
Step Four
Place the mounting blocks inside the hole at either end. Use two
#8 x 1" flat-head wood screws to secure them in place.
Mounting Block
(4) #8 x 1"
Flat-Head
Wood Screws
Mounting
Block
4
TSS-FMK4000
Step Five
Attach speaker wires as described in the speaker’s owner’s
manual and, using four #8 x 1-1/8" pan-head wood screws
provided, screw the speaker assembly into place, making sure
that the screws anchor themselves into the mounting blocks
behind the drywall.
(4) #8 x 1-1/8"
Pan-Head
Wood Screws
Step Six
Apply the sealing strips to either side of the speaker to cover the
remaining openings of the cutout in the drywall.
Sealing Strip
5
TSS-FMK4000
Step Seven
Remove the paper cover from the gasket on the speaker-facing
side of the frame. Place the frame over the in-wall assembly and
snap it into place.
Remove Paper Cover
From Gasket
Frame
Center Speaker In-Wall Installation
6
TSS-FMK4000
Satellite Installation Exploded View
For satellite installation, repeat the steps but cut the hole in
a vertical direction, perpendicular to the floor.
Satellite Speaker
In-Wall Installation
7
TSS-FMK4000
© 2004 Harman International Industries, Incorporated
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (USA only)
Infinity is a registered trademark, and Total Solutions is a trademark, of Harman International Industries, Incorporated.
Part No. 400-OMINKIT 10/04
Infinity continually strives to update and improve existing products, as well as create new ones.
The specifications and construction details in this and related Infinity publications are therefore
subject to change without notice.
|
Jacuzzi Outdoor Shower SUMMER RAINTM 2 WALL 3 WALL WALK IN SHOWER SYSTEMS User Manual
JVC Camcorder Accessories 0398AYVUNSW User Manual
JVC CD Player XM R70 User Manual
JVC Personal Computer LYT1116 001A User Manual
JVC Speaker System CA MXKA3 User Manual
JVC Stereo Receiver 0497OFYOTKJEMEN User Manual
Kicker Speaker ZK500 User Manual
KitchenAid Coffeemaker KCM222 User Manual
Kodak Film Camera AS 2569 User Manual
Konica Minolta Oxygen Equipment PULSOX 300i User Manual