SpeedSteam
Instruction Booklet
Iron
KI450/KI480
80_IB_D12.indd
1
5/12/12 10:28 A
Contents
Kambrook Recommends
Safety First
p4
Your Kambrook SpeedSteam Iron
Operating Instructions
p6
p7
Care and Cleaning
p11
3
80_IB_D12.indd
3
5/12/12 10:28 A
Kambrook Recommends Safety First
IMPORTANT: Please
retain your instruction
book for future use.
At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently use
and trust our products. We ask that any electrical appliance that you use
be operated in a sensible fashion with due care and attention placed on
the following important operating instructions.
Important Safeguards For Your Kambrook
SpeedSteam Iron
•
Carefully read all instructions before
operating the Kambrook SpeedSteam
Iron for the first time and save for
future reference.
dropped, immediately cease use of
the appliance and return the entire
appliance to your nearest authorised
Kambrook Service Centre for
examination, replacement or repair.
•
To protect against electric shock, do
not immerse the iron, cord or plug in
water or any other liquid.
•
•
Store the unit out of reach of children.
Do not leave the appliance
unattended when in use.
•
•
Do not use the iron for anything other
than its intended use.
•
•
The iron must be used and rested on a
stable surface
Always turn the Variable Temperature
Control to minimum, switch off at
the power outlet, then unplug the
appliance when not in use.
When placing the iron on its heel,
ensure that the surface on which the
heel is placed is stable.
•
•
Allow the iron to cool completely
before storing in an upright position
on its heel.
•
•
The iron is not to be used if it has been
dropped, if there are visible signs of
damage or if it is leaking.
Do not touch hot surfaces. High
temperatures are generated during
use, which could cause burns. Always
use the handle and warn others
(especially children) of the possible
dangers of burns from steam, hot
water or hot soleplate, especially
when ironing vertically.
Do not allow the iron to lay flat on the
soleplate when stored as water may
seep through the steam holes, if the
tank is not empty.
•
•
Always test the iron on a small,
discreet part of the fabric to be ironed
to ensure the temperature is not set
too high.
•
Regularly inspect the supply cord,
plug and actual appliance for
any damage. If damage is found
in any way, or the iron has been
Always store the iron in the upright
position on its heel. Do not leave the
iron unattended while connected or
on an ironing board.
4
80_IB_D12.indd
4
5/12/12 10:28 A
•
•
Do not use outdoors or in bathrooms.
•
Always switch off at the power outlet,
then unplug the appliance from the
outlet:
Do not store the iron with water in the
water tank. Always empty the tank
after use. Ensure the iron is cool before
storing or wrapping the cord around
the storage heel facility.
-Before filling with water or emptying it.
-Before leaving it unattended.
-Before cleaning and maintenance,
unless otherwise specified in this
booklet.
-Immediately after use.
Important Safeguards For All
Electrical Appliances
•
Fully unwind the power cord before use.
•
This appliance is for household use
only. Do not use this appliance for
anything other than its intended use.
Do not use in moving vehicles or
boats. Do not use outdoors.
•
Connect only to a 230V or 240V
power outlet.
•
•
Do not let the power cord hang over
the edge of a bench or table, touch
hot surfaces or become knotted.
Misuse may cause injury.
•
The installation of a residual current
device (safety switch) is recommended
to provide additional safety protection
when using electrical appliances. It
is advisable that a safety switch with
a rated residual operating current
not exceeding 30mA be installed in
the electrical circuit supplying the
appliance. See your electrician for
professional advice.
To protect against electric shock, do not
immerse the power cord, power plug or
appliance in water or any other liquid or
allow moisture to come in contact with
the part, unless it is recommended in
the cleaning instructions.
•
The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by
a person responsible for their safety.
•
•
Always turn the appliance to the OFF
position, switch off at the power outlet
and unplug at the power outlet when
the appliance is not in use.
Before cleaning, always turn the
appliance to the OFF position, switch
off at the power outlet, unplug at
the power outlet and remove the
power cord, if detachable, from the
appliance and allow all parts to cool.
•
•
Children should be supervised to
ensure that they do not play with
the appliance.
It is recommended to regularly inspect
the appliance. To avoid a hazard, do
not use the appliance if power cord,
power plug or appliance becomes
damaged in any way. Return the entire
appliance to the nearest authorized
Ronson service centre for examination
and/or repair.
•
•
Do not place this appliance on or
near a heat source, such as hot plate,
oven or heaters.
Position the appliance at a minimum
distance of 20cm away from walls,
curtains and other heat or steam
sensitive materials and provide
adequate space above and on
all sides for air circulation.
•
Any maintenance other than cleaning
should be performed at an authorised
Ronson Service Centre.
5
80_IB_D12.indd
5
5/12/12 10:28 A
Your Kambrook SpeedSteam Iron (KI480 shown)
1. Shot of steam button: For an extra
burst of steam on thick fabric or
tough creases
11. Long textile cord with 360° cord outlet
for better reach and more flexibility:
2.5 metre
2. Steam control: Allows you to
select how much or how little
steam you require
12. Power Indicator light: Illuminates
when the iron is plugged into a
power outlet and switched on
3. Water tank inlet: Large inlet for easy
13. Auto Off light (KI480 only):
Will blink to indicate that the
iron has automatically shut off
when left unattended
filling of water tank
4. Fine mist spray nozzle
5. Fine mist spray: To dampen fabric
especially for dry ironing at low
temperatures when steam isn’t
available (also assists in removing
stubborn creases)
6. Temperature control: Selection
of fabric temperatures from MIN
(synthetic) to MAX (linen)
7. Self-clean function
8. 260ml easy to fill water tank
9. 2000W
Not Shown
•
Vertical shot of steam: Removes
creases and freshens hanging curtains
and clothes. Ideal for delicate fabrics
which require steam only
•
•
•
Anti-drip system: Stops water
from dripping
Continuous steam: Removal of
creases throughout ironing time
10. Non-stick soleplate: For easy gliding
Accessory: Water cup for filling the iron
over all fabric types
6
80_IB_D12.indd
6
5/12/12 10:28 A
Operating Instructions
Before First Use
Remove any promotional material or
packaging from the iron.
NOTE: As an important part of
our quality control process, your
iron has been individually tested.
As a result, you may notice a
small amount of condensation
or water droplets on the inside of
the water tank. There is no need
for concern.
Remove any sticker or protective cover
from the soleplate. When operating the
iron for the first time, iron on an old piece
of fabric to ensure that the soleplate and
water tank are completely clean.
When the iron is used for the first time,
some vapour may emit. After a short
while however, this will cease. The
vapour is due to the initial heating of
the materials used in the iron. It is safe
and will not harm the performance of
the iron.
Setting the Temperature
Before commencing ironing, first sort
the items to be ironed according to the
International Textile Care Labelling Code
or by the type of fabric. Iron fabrics
that require the lowest temperatures
first. Work through to the fabrics
requiring higher temperatures. Both the
Temperature Control and most items of
laundry have markings corresponding
with this code (see Table A).
Table A
on label means: “This article cannot be ironed”
[e.g. chlorofibre, acrylic, elastodiene]
NOTE:
Temperature
Control
Variable Steam
Control
Label Code
Kind of Textile
[see garment
instruction]
[advised position]
synthetic
modacry
MIN
polypropylene
polyurethane
acetate
DRY
triacetate
matalized
cupro
plyamide [nylon]
polyester
modal
viscose [rayon]
silk
MIN STEAM
wool
cotton
LINEN
MAX
MAX STEAM
linen
7
80_IB_D12.indd
7
5/12/12 10:28 A
Operating Instructions continued
Stand the iron on its heel and turn the
Temperature Control to MIN.
To Operate the Steam Control
As per the indications on the
Temperature Control and in Table A (see
section ‘Setting the Temperature’) steam
ironing is only possible at higher ironing
temperatures, indicated with Cotton/
Linen on the Temperature Control.
Plug the power cord into a 230V or 240V
power outlet and switch on. The Power
Indicator light will illuminate while the iron
is plugged into an outlet and switched on.
Plug the power into a 230V or 240V
power outlet and switch the power on.
The Power Indicator light will illuminate
while the iron is plugged into an outlet
and switched on.
NOTE: for KI480 only, the Power
Indicator light will remain on even
if Auto Off has been activated.
Select the temperature setting required
by rotating the Temperature Control dial
so that the desired setting is aligned with
the Temperature Indicator.
NOTE: for KI480 only, the Power
Indicator light will remain on even
if Auto Off has been activated.
Your Kambrook iron is now ready for use.
Set the Temperature Control to the
required position within the steam range.
CAuTION: The iron
incorporates a thermal
safety fuse to protect the
iron from over-heating.
However the iron should
not be left unattended
while it is connected to
the power outlet. Special
care should always be
taken when there are
children in the home/
vicinity of the iron.
Set the Steam Control (on top of the
handle) to the required setting.
Your Kambrook iron is now ready for use.
IMpORTANT: If the iron is
set to a low temperature
on the Temperature
Control (i.e. synthetic
or silk) and also on any
of the steam control
settings, there may
be leakage from the
soleplate. This is due to
the iron temperature not
being high enough to
vaporise the water and
create steam.
Steam Ironing
When filling the iron with water, ensure
that the iron is unplugged. Set the
Steam Control to the MIN position and
holding the iron at an angle, use the
water cup supplied to fill the water tank.
Never exceed the maximum water level
as indicated (MAX) on the side of the
water tank.
Therefore, ensure that
the steam control is
always set to correspond
with the setting on the
temperature control as
seen in Table A
Tap water can be used in your
Kambrook SpeedSteam Iron unless
it is particularly hard, in which case
it is recommended that distilled or
demineralised water be used.
(see section ‘Setting
the Temperature’).
8
80_IB_D12.indd
8
5/12/12 10:28 A
How To Use Shot Of Steam
Dry Ironing
The shot of steam provides an extra burst
of steam which is ideal for the removal
of stubborn creases and wrinkles during
STEAM or DRY ironing.
Turn the steam selector to the MIN position.
This minimises the steam flow should there
be any water in the tank.
Select the required setting on the
Temperature Control for the fabric
being ironed.
Turn the Temperature Control to the
hottest setting. Ensure the Steam Control
corresponds to the setting on the
Temperature Control.
For best results, let the iron sit in an
upright position for a couple of minutes
in order for the iron to reach the desired
temperature.
Lift the iron slightly above the surface of
the fabric, press the Shot of Steam button
down firmly and release it during ironing.
An intense burst of steam penetrates
deep into the fabric.
Using the Fine Mist Spray
The Fine Mist Spray can be used to
dampen difficult fabrics, dry areas,
woollen items and accidental creases.
Firmly press the spray button (located on
the handle of the iron) to produce a fine
spray of water ahead of the iron.
NOTE: For optimal steam quality,
wait an interval of at least 4
seconds between presses of the
Shot of Steam button.
The spray can also be used with delicate
fabrics (synthetic) which are ironed at
low temperatures and therefore cannot
be steam ironed.
Vertical Steam Shot
The Vertical Steam Shot allows you to
use the iron for vertical applications. This
is especially useful for getting wrinkles
out of hanging garments, curtains, wall
hangings etc.
NOTE: If the spray function is
operated during dry ironing,
ensure that there is sufficient
water in the water tank. If dry
ironing for more than 20 minutes,
the water tank should be
Hold the iron vertically, in front, a slight
distance from the item to be steamed
and press the Shot of Steam button.
emptied to prevent over heating
any water present.
CAuTION: Never use
the vertical steam shot
while clothes are on the
body or direct the steam
towards people.
9
80_IB_D12.indd
9
5/12/12 10:28 A
Operating Instructions continued
Anti-Drip System
The Kambrook SpeedSteam Iron is
equipped with an Anti-Drip System. The
iron will automatically close the steam
valve when the soleplate temperature
is too low to produce steam. When this
happens you will hear a click sound. It is
safe and will not harm the performance
of the iron.
Fig. 2
This is the reason the Fine Mist Spray
should be used when ironing delicate
fabrics at low temperatures.
Once the iron has shut itself off, the Auto
Off light will blink to indicate that the iron
has switched off.
The steam valve will open once the
soleplate has reached the temperature
required to create steam.
To reactivate the iron, simply move the
iron. The Auto Off light will stop blinking
and remain illuminated.
Safety Auto Off (KI480 Only)
The Safety Auto Off feature is designed to
switch the iron off if forgotten.
After Each Use
When the iron is left in the upright position
it will shut off in approximately 8 minutes,
followed by six beeps.
Set the steam selector to the MIN position
and turn the Temperature Control to MIN.
Switch the power off at the power outlet
and disconnect the power cord from the
power outlet.
Open the Water Tank Inlet and (over a
sink or bucket) invert the iron to empty
the remaining water from the tank.
Stand the iron in an upright position and
allow to cool.
CAuTION: Safety auto
off is designed as a safety
feature only. Irons should
not be left switched
Fig. 1
When left in the ironing position, it will
switch off in approximately 30 seconds,
followed by six beeps.
on deliberately while
unattended. If safety auto
off has activated and no
further ironing is required,
we recommend that
the iron is switched off
at the power outlet
and unplugged.
10
80_IB_D12.indd 10
5/12/12 10:28 A
Care and Cleaning
To ensure your iron maintains optimum
performance it is recommended that it
be cleaned using the Self-Clean function
to remove scale or impurities.
CAuTION: Only push and
hold the Self-Clean button
when you want to activate
the self cleaning function.
Do not push and hold
whilst ironing.
•
Set the steam selector to the
MIN position.
•
Fill the water tank up to the
maximum level (MAX) with the
water cup supplied.
Boiling water and steam
will drip from the holes in
the soleplate during the
cleaning process. Due
caution and attention
should be exercised.
•
•
Set the Temperature Control to MAX
(linen) setting.
Place the iron in the upright position,
insert the plug into the power outlet
and switch the iron on. The Power
Indicator light will illuminate.
Cleaning the Soleplate
and Exterior
Ensure that the iron is disconnected from
the power outlet.
•
•
Allow the iron to heat and let stand
sitting upright for up to five minutes.
Switch the iron off at the power outlet
and remove the plug.
To remove residue which may have built
up from certain fabric finishes, clean the
soleplate with a rough cloth that has
been soaked in a vinegar and water
solution. Dry thoroughly with a soft cloth.
•
•
•
Hold the iron horizontally over the sink.
Press and hold the SELF CLEAN button.
Water will drip through the holes in the
soleplate. Move iron until all water has
dripped out of the water tank.
To clean the steam holes, simply
use a damp cloth to wipe away
build up of lint or starch from inside the
steam holes.
NOTE: Once you have used the
Self-Clean function, it is normal
for some water to remain in the
water tank. This is due to the
Anti-Drip System preventing
the tank from being emptied
completely. This will not affect the
performance of the iron.
Wipe the outer housing with a soft, damp
clean cloth and polish with a dry cloth.
NOTE: Never use abrasives
or scouring pads to clean the
soleplate. Avoid hard contact
with metal objects. Do not
scratch or damage the surface of
the soleplate.
Repeat the Self-Clean process if the iron
still contains a lot of impurities.
Do not use harsh or abrasive cleaners
as they may damage the surface of the
iron. Never immerse the iron in water or
any other liquid.
11
80_IB_D12.indd 11
5/12/12 10:28 A
Kambrook - Australia
Kambrook - New Zealand
Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019 Australia
Customer Service Line
1300 139 798
Customer Service Fax
1800 621 337
Private Bag 94411
Botany, Manukau Auckland
2163 New Zealand
Customer Service Line/Spare Parts
0800 273 845
Customer Service Fax
0800 288 513
Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book.
Issue D12
80_IB_D12.indd
1
5/12/12 10:28 A
|